PRODUCTS
VR

TH350GS Thermal Paste: A High-Reliability Thermal Interface Material for Modern Electronics

Heat is the silent enemy of every electronic device. Processors throttle, LED chips dim, and power modules age early when thermal energy cannot escape efficiently. A high-quality thermal interface material (TIM) closes the microscopic air gaps between a chip and its heatsink — and that single layer can decide whether a product lasts one year or ten.

TH350GS Thermal Paste is engineered for exactly this job. With thermal conductivity above 1.195 W/m-K, low thermal impedance, and a clean white finish that makes coverage easy to inspect, it is a practical choice for OEM assembly lines, repair technicians, and product designers who need repeatable cooling performance.

 

TH350GS Thermal Paste — professional white finish for clean, verifiable assembly

Why the Thermal Interface Matters

Even polished metal surfaces are rough at the microscopic level. Without a thermal compound, air pockets act as insulators and heat accumulates at the joint. A semi-flowing paste such as TH350GS wets those micro-gaps, creating a continuous path for heat to move from the semiconductor die into the heatsink or housing.

The result is a lower temperature rise under load, more stable clock speeds in computing applications, and slower lumen depreciation in LED lighting systems.

Key Features and Technical Highlights

· Clean white color (visual inspection): a smooth white finish delivers a professional look on CPU coolers, LED boards and power modules, and makes coverage easy to verify during assembly.

· Thermal conductivity > 1.195 W/m-K (GOST 8.140-82): transfers heat quickly from processors, chipsets and LED chips to the heatsink, keeping devices cooler under load.

· Thermal impedance < 0.20 °C·in²/W (ASTM D1470): low interface resistance minimizes the temperature gap across the joint for more efficient cooling.

· Specific gravity > 2 g/cm³ (ASTM D1475): a densely filled formulation provides consistent, repeatable thermal performance batch after batch.

· Evaporation < 0.005% (Fed.Std.791, 24 h at 150°C): minimal evaporation preserves the paste layer for long-term reliability in always-on electronics.

· Oil bleed < 0.05% (Fed.Std.791, 150°C / 24 h): very low bleed prevents oil separation that could stain components or weaken thermal contact.

· Dielectric constant > 5.0 at 100 Hz (ASTM D150): controlled dielectric properties suit sensitive IC and BGA assemblies where stable electrical behavior is required.

· Semi-flowing viscosity: spreads smoothly into micro-gaps between chips and heatsinks — quick and tool-free to apply on production lines.

· Thixotropic index 380 ± 10 (1/10 mm, GB/T 269): stable consistency resists pump-out and keeps the paste in place through thermal cycling.

· Operating temperature -50°C to 240°C: reliable from extreme cold to high heat, covering automotive electronics, power supplies, outdoor LED lighting and telecom/5G equipment.

Typical Applications

 

Efficient heat transfer at every interface — from board-level chips to full heatsinks

· CPU and GPU coolers in computing equipment

· LED modules, LED boards and outdoor LED lighting

· Switching power supplies and power modules

· Automotive electronic control units

· Telecom and 5G base station equipment

· Sensitive IC, BGA and chipset assemblies

How to Apply TH350GS

Proper application is simple and takes less than a minute. The goal is a thin, continuous layer — thicker is not better.

 

Application steps: dispense, spread evenly, finish with a thin layer

1. Clean both contact surfaces (chip top and heatsink base) with a lint-free cloth.

2. Dispense a small amount of TH350GS onto the center of the chip.

3. Spread the paste with a spatula or gloved fingertip into a thin, even layer that covers the whole surface.

4. Mount the heatsink, tighten the fasteners evenly, and power on. No cure time is required.

Technical Specifications at a Glance

Color / AppearanceClean white, smoothVisual inspection
Thermal Conductivity> 1.195 W/m-KGOST 8.140-82
Thermal Impedance< 0.20 °C·in²/WASTM D1470
Specific Gravity> 2 g/cm³ASTM D1475
Evaporation (24 h @ 150°C)< 0.005%Fed.Std.791
Oil Bleed (150°C / 24 h)< 0.05%Fed.Std.791
Dielectric Constant (100 Hz)> 5.0ASTM D150
ViscositySemi-flowing—
Thixotropic Index (1/10 mm)380 ± 10GB/T 269
Operating Temperature-50°C to 240°C—

   

Why Buyers Choose TH350GS

For OEM buyers, the combination of dense filler loading (specific gravity > 2 g/cm³), controlled thixotropy, and very low evaporation and oil bleed means each batch behaves like the last. For field technicians, the clean white color and semi-flowing texture make it easy to confirm coverage and finish a rework job quickly. For end users, the broad -50°C to 240°C range means the same paste works from automotive modules to high-temperature power electronics.

Request a Quote or Sample

Ready to evaluate TH350GS Thermal Paste for your next project? Contact our team for samples, technical data sheets, pricing, and OEM / private-label options:

Contact Us :

Company: Gorcci International Limmited

Email: info@gorcci.com

WhatsApp / Mobile / Wechat: +86 1752101 7986


Basic Information
  • Year Established
    --
  • Business Type
    --
  • Country / Region
    --
  • Main Industry
    --
  • Main Products
    --
  • Enterprise Legal Person
    --
  • Total Employees
    --
  • Annual Output Value
    --
  • Export Market
    --
  • Cooperated Customers
    --

Recommended

Send your inquiry

GET IN TOUCH WITH US

We sincerely invite all interested companies to contact us for more information.

Chat
Now

Send your inquiry

Choose a different language
╳
English
עִברִית
Latin
Deutsch
français
Tiếng Việt
Türkçe
العربية
ภาษาไทย
Português
Українська
русский
Español
Current language:English